EasyShort – Screwed prosthetic solution

All the abutments, analogues and transfers are made of titanium grade 5 (Ti6Al4V). The fastening screw ELPSC1 is included in the packaging of the abutmentsi. Tighten to 30 N*cm using the torque ratchet wrench  ELSAPK with the torque ratchet  ELKWD.

Octagonal abutment

Code
ELMEO
 

Castable for octagonal abutment

Code Indication For implant (mm)
EDCEOC For circulars Ø 4.0
EDCEOE For mono implants Ø 4.0
ENCEOC For circulars Ø 4.75 e Ø 5.25
ENCEOE For mono implants Ø 4.75 e Ø 5.25


 

Titanium cap for octagonal abutment

Code Height mm For implantsi (mm)
EDMEOA 15 Ø 4.0
ENMEOA 15 Ø 4.75 e Ø 5.25


 

Esthetic octagonal abutment

Code Height (mm)
ELMEO15 1,5
ELMEO3 3.0
ELMEO4 4.0


 

Titanium cap for esthetic octagonal abutment

Code Height mm
ELMEOC 15


 

Castable for esthetic octagonal abutment

Code Height mm
ELMEOCC 15


 

Protection for octagonal abutment

Code For implants
ENMEOH Ø 4.75 e Ø 5.25 mm


 

Octagonal abutment analogue

Analogo-del-moncone-ottagonale-dip

Code Colour For implants (mm)
EDAMEO Gold Ø 4.0
ENAMEO Blue Ø 4.75 e Ø 5.25


 

Octagonal abutment transfer

Transfer-del-moncone-ottagonale-dip

Code Colour For implants (mm)
EDICE Gold Ø 4.0
ENICE Blue Ø 4.75 e Ø 5.25


 

Implant analogue

Analogo-impianto-dip

Code Colour For implants (mm)
EDAN Gold Ø 4.0
ENAN Green Ø 4.75 e Ø 5.25

 

Implant transfer

Transfer-per-impianto-dip

Code Colour For implants (mm)
EDTRA Gold Ø 4.0
ENTRA Green Ø 4.75 e Ø 5.25

 

Impression transfer technique for the octagonal abutment ELMEO

To transfer the location of the octagonal abutment onto a casting, proceed by insertingthe transfer for octagonal abutment EDICE or ENICE and secure it with the long fastening screw ELPSC2 included in the packaging of the transfer. Tighten using the manual screwdrivers ELCSK1 or ELCSK2 or the contra-angle wrench ELPSCAK. Then proceed with the impression using a slotted spoon. Before removing the impression, loosen the fastening screw releasing the transfer. Insert the implant analogue for octagonal abutments EDAMEO or ENAMEO, assembling it to transfer EDICE or ENICE using the fastening screw which has been previously loosened.Now it is possible to send the impression to the laboratory. For the esthetic octagonal abutments(ELMEO15, ELMEO3, ELMEO4) take the impression at implant level.

Implant impression transfer technique

To transfer the location of the fixture onto a casting, proceed bye inserting the implant transfer EDTRA or ENTRA in the implant and secure it with the long fastening screw ELPSC2 included in the packaging of the transfer.Tighten using the screwdrivers ELCSK1 or ELCSK2 or the contra-angle wrench ELPSCAK. Then proceed with the impression using a slotted spoon. Before removing the impression, loosen the fastening screw releasing the transfer. Insert the implant analogue EDAN or ENAN, assembling it to its transfer EDTRA or ENTRA using the fastening screw previously loosened. Now it is possible to send the impression to the laboratory.